Temperature Controller

Product Details:

Main Features –

• Relay output : Compressor + Heater + Evap. Fan.
• Compressor protection algorithm.
• Auto/Man defrosting facility (Time/ Temp based).

Input & Output –

• Relay Output 1 & 2 : 8(3)A for Heater & Evap. Fan.
• Relay Output 3 : 8(3)A Compressor.
• Temp. Sensor Input : (Room & Evap. Coil).

Product Details:

• The Sub-Zero Series SZ-7521-P are aesthetically superior versions of their predecessors.
• They are specifically designed for refrigeration applications wherein the compressor cuts off at set point and is restarted as a temperature of set point plus differential.

Product Details:

• Main Features
• Switch off relay at setpoint.
• Alarm output for High / Low Humidity.
• Dehumidification / Humidification.

• Relay output : 8(3)A.
• Alarm relay : 5A.
• Humidity Sensor Input : 1 RH Probe.

Product Details:

• The new SZ-7510T/7569T are the next generation of Subzero controllers. Their IP ratings are greatly improved and have an excellent iconic display. The touch feature whilst increasing reliability also gives a great user experience. These controllers designed for refrigeration have several features specially designed for safety of compressors. They work on the system that the compressor cuts off at set point and is restarted at a temperature of set point + differential. Their operation is very user friendly and is easily understood with the examples in the instructions below. Various parameters help set up the instruments functions for different applications. The SZ-7510T/7569T can be used for several applications with a O O measuring range from -45 C to 99 C.
• CAUTION
• Notice: The information in this document is subject to change in order to improve reliability , design or function without prior notice and does not represent a commitment on the part of the company. In no event will the company be liable for direct, indirect, special, incidental or consequential damage arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. No part of this manual may be reproduced or transmitted in any form or by any means without the prior written permission of the company. 
• WIRING: The probe and its corresponding wires should never be installed in a conduit next to control or power supply lines. The electrical wiring should be done as shown in the diagram. The power supply circuit should be connected to a protection switch. The terminals admit wires of upto 2.5sq mm. 
• WARNING: Improper wiring may cause irreparable damage and personal injury. Kindly ensure that wiring is done by qualified personnel only. 
• Maintenance: Cleaning: Clean the surface of the controller with a soft moist cloth. Do not use abrasive detergents, petrol, alcohol or solvents. 
• Controller: Controller should be installed in a place protected by vibration, water and corrosive gasses and where ambient temperature does not exceed the values specified in the technical data.
• Installation: Fixing and dimensions of panel models. To fix the unit, slide the fastener 1 through the guides 2 as per the position shown in the figure. Move the fastener in the direction of the arrow, pressing tab 3 it permits to move the fastener in the opposite direction of the arrow. 
• Probe :To give a correct reading, the probe must be installed in a place protected from thermal influences, which may affect the temperature to be controlled.

Product Details:

• Introduction 
• The new 7569T(Touch Button) are the next generation of Subzero controllers.
• Their IP ratings are greatly improved and have an excellent iconic display.
• The touch feature whilst increasing reliability also gives a great user experience.
• These controllers designed for refrigeration have several features specially designed for safety of compressors.
• They work on the system that the compressor cuts off at set point and is restarted at a temperature of set point + differential. 
• Their operation is very user friendly and is easily understood with the examples in the instructions below. Various parameters help set up the instruments functions for different applications.

Product Details:

• Cooling & Heating output
• Memory retention, time delay for compressor protection
• Auto operation incase of sensor error
• Power switch

• Relay Output: SZ-7510 P - 8(3)A / SZ-7569P - 20A (Inductive).
• Temp. Sensor 

• Panel cutout:  Screw terminals: Admit 
• Spade terminals for compressors 

Product Details:

• Manufacturer & Supplier of SZ-7510E / SZ- 7569E Subzero Temperature Controllers in India.
• We have established ourselves as a renowned manufacturer and supplier in offering an attractive range of Controller With 10 / 20A Relay / SZ-7510E / 7569E. These products are stringently tested on various parameters by our quality controllers to ensure its flawlessness. Further, these products are highly appreciated in the market for its features like longer service life, accurate results, dimensional accuracy and high performance.
• Main Features:
• Cooling output
• Memory retention, time delay for compressor protection
• Auto operation incase of sensor error